How to Size an LTO Battery for Your Car Audio System
Work out your system's current, how long the battery can supply it, and what your alternator covers. Includes a table for 1000W to 5000W systems.
Short answer: estimate your current draw from your amplifier's RMS power, subtract what your alternator can supply, then choose a capacity that covers the rest for as long as you want to play.
Step 1: Estimate the current
Use this formula:
Current (A) = RMS power (W) ÷ amplifier efficiency ÷ voltage (V)
The chart below uses 13.8V and 85% efficiency. Check your amplifier's own specification, because efficiency varies by design.

Step 2: See how long a pack lasts at full power
This table shows the worst case: full RMS power, all the time, with no help from the alternator. Real music draws far less on average, so treat these as a floor rather than a prediction.
| RMS power | Current | 30Ah (414Wh) | 40Ah (552Wh) | 45Ah (621Wh) |
|---|---|---|---|---|
| 1000W | 85A | 21 min | 28 min | 32 min |
| 2000W | 171A | 11 min | 14 min | 16 min |
| 3000W | 256A | 7 min | 9 min | 11 min |
| 4000W | 341A | 5 min | 7 min | 8 min |
| 5000W | 426A | 4 min | 6 min | 6 min |
These are calculated from nominal energy at 85% efficiency. They are not test results, and voltage drop and temperature will change them.
Step 3: Check the current limit
A battery's C-rate is its current relative to its capacity. As Battery University explains, a 1Ah battery at 1C provides 1A for one hour. So a 40Ah pack at 256A is running at about 6.4C.
In a 6S1P pack, the full current passes through every cell, so the cell's limit is the pack's limit. The cell maker's published reference data, linked in the sources, does not give continuous or pulse current limits for these cells, so we do not quote any here. Ask for the specification of the cells in your pack. Our packs have no BMS, so a pack can only supply what the lowest of the cell, the busbars, the cables and the fuse allows, and nothing in the pack cuts off an overload for you. Bass peaks are short, but they still count against the pulse limit. For systems of 3000W or more, contact us with your amplifier details before you order.
Step 4: Count your alternator
Your alternator supplies part of the load while the engine runs. Find its rating, then subtract what the car itself uses.
Worked example. These numbers are assumptions, so use your own:
- 3000W RMS system, 256A at full power
- Loud music averaging a quarter of full power: about 64A
- 40A spare from the alternator
- The battery supplies the remaining 24A
- A 40Ah pack could cover that for about 100 minutes, in theory, while still supplying the short peaks
Quick guide
| If you want | Consider |
|---|---|
| The smallest and lowest-cost option | 30Ah |
| A middle option with more reserve | 40Ah |
| The most capacity in one pack | 45Ah |
All three share the same 6S1P construction and 26 × 22 × 15.5 cm case, so capacity does not change the space you need.
Do not forget the wiring
High current needs suitably sized cable, secure connections and a fuse close to the battery. Use a qualified installer if you are unsure about any of this.
Next steps
See our 12V LTO packs, or compare LTO and AGM.
Sources
- Gree Altairnano official site, 40Ah/45Ah LTO cylindrical cells (reference data, read 10 November 2026; no current limits listed)
- Battery University, BU-402: What Is C-rate?
Last reviewed 11 November 2026. Calculations are estimates for planning, not measured results.